Before connecting the controller to the power supply cell, please turn on the transmitter at a minimum throttle control position. A minimum position of the control lever is signaled by a long audible beep. When the signal is finished, the controller is ready for operation.

The course of the motor capacity control (not the speed) is proportional to the offset of the motor control lever, which enables you to finely adjust the motor capacity within the entire capacity range.

If the current fuse is blown out in the case of controller overload, it is possible to reset the controller by setting the lever to a minimum position and restarting the system.

TECHNICAL SPECIFICATIONS

Max. Continuous Load	3 Amps Continuous
Electronic Fuse	3.3 Amps
Nominal Voltage	3.7 V, Li Ion and LiPoly (single cell)
Operating Temperature	0 to 40° C.
Power Supply Voltage	2.7 to 5.5 Volts (1 LiPooly cell)
Clock Frequency	16 kHz
Dimensions	13 mm x 9 mm x 2 mm
Weight	0.22 grams without wires (1.0 g with wires and plugs)

SCSH-3BL: $69.00 each Canadian

Top of Page
Return to Catalogue Index
To Process Your order (Checkout)

SCSH-6BL - 6 Amp, 1.3 g Brushless Controller for Micro Outruners

Weight 1.8 g.

6 AMP BRUSHLESS CONTROLLER

The well-fitting controller for small brushless outruner motors up to 6A.
This new lightweight 1.8g controller for max. power of brushless motors at minimum weight can supply a constant current of 6 Amp (burst 8A) to the motor! Controller characteristics and different low voltage detections for Li-Polymer and for NiMh cells can be programmed by the customer.

STARTUP

1. After connection of the controller to the battery and setting of the transmitter control stick to STOP, you will hear 3 ascending sounds caused by the connected motor acting as a signal transmitter.

2. The unit is ready to use.

TECHNICAL SPECIFICATIONS

Max. Load	6 Amps continuous (8 Amps intermitant)
Nominal Voltage	LiIon and LiPoly	2 to 3 cells (6 to 13 Volts)
Motor rpm reduction for LiPo and NiMh	MOS-FET RISC Microcontroller	Safe Start with receiver signal check
Clock Frequency	14 kHz.
BEC	5.0V. max. 0.8 A
Dimensions	6 mm x 24 mm x 12 mm
Weight	1.8 grams without wires (3 g w/wires)

SCSH-6BL: $54.00 each Canadian

Top of Page
Return to Catalogue Index
To Process Your order (Checkout)

SCSH-10BL - 10 Amp, Auto Program Brushless Controller for Micro Outrunners

Weight 9.8 g.

with all wires

BLUE BIRD 10 AMP BRUSHLESS CONTROLLER

Has Auto Detection for control mode selection for a specific motor.

A programable switch permits Brake or Non-Brake mode.

Automatically monitors cell count of NiCd, NiMH or Lithium batteries.

When battery Voltage drops to the pre-set level, motor output decreases gradually rather than suddenly.

Before you connect the battery, always switch on the flight pack and the transmitter, making certain that the throttle is at its lowest setting.

TECHNICAL SPECIFICATIONS

Max. Load	10 Amps continuous (15 Amps for 60 seconds only)
Working Voltage	NiCd and NiMH	6 to 12 cells (6 to 15 Volts)
	LiIon and LiPoly	2 to 4 cells (6 to 15 Volts)
Working Temperature	0° to 45°C.
Max. RPM	6-Pole Motors 70,000 RPM
	12 Pole Motors 35,000 RPM
Weight	9.8 g. with all wires

SCSH-10BL: $41.50 each Canadian

Top of Page
Return to Catalogue Index
To Process Your order (Checkout)

SCSH-20BL - 20 Amp, Auto Program Brushless Controller for Micro Outrunners

Weight 19 g.

with all wires

MTM / Dualsky 20 AMP BRUSHLESS CONTROLLER

Has Auto Detection for control mode selection for a specific motor.

A programable switch permits Brake or Non-Brake mode.

Automatically monitors cell count of NiCd, NiMH or Lithium batteries.

When battery Voltage drops to the pre-set level, motor output decreases gradually rather than suddenly.

Before you connect the battery, always switch on the flight pack and the transmitter, making certain that the throttle is at its lowest setting.

TECHNICAL SPECIFICATIONS

Max. Load	20 Amp 20 Amps continuous (25 Amps for 60 seconds only)
Working Voltage	NiCd and NiMH	6 to 12 cells (6 to 15 Volts)
	LiIon and LiPoly	2 to 4 cells (6 to 15 Volts)
Working Temperature	0 to +450 to 45°C.
Max. RPM	6-Pole Motors 70,000 RPM
	12-Pole Motors 35,000 RPM
Weight	19 g. with all wires

SCSH-20BL: $66.00 each Canadian

Top of Page
Return to Catalogue Index
To Process Your order (Checkout)

SCSH-3V Sub Micro ESC by SKY HOOKS & RIGGING, 3 Volt Throttle Cut Down for lithium polymer cells

0.6 g. without wires

Controller Technical Data

Functions =	Forward, Soft Start, BEC, Cut,
Nominal Voltage =	6 to 10.5 V. (15 V. absolute maximum)
Voltage Drop =	<17 mV / 1 A
Current =	7 Amps Continuous 9 Amps Maximum
Clock frequency =	4 kHz
BEC =	3 V at 0.8 A
Motor rpm reduction =	Voltage < 3 V.
Size =	10mm x 6mm x 3mm
Mass (without wires) =	0.6 g
Mass (with wires and connectors) =	1.0 g

Operation

The controller does not switch off power, but reduces power to 1/4 throttle when it detects that the battery has dropped below 3 Volts. This permits slow flyers to land safely.

Designed for single cell Polymer applications, where light weight is essential.

SCSH-3V: $39.00 each Canadian

Top of Page
Return to Catalogue Index
To Process Your order (Checkout)

SCSH-7A-3 ESC by SKY HOOKS & RIGGING, 3 Volt Throttle Cut Down

1.8 g. by Sky Hooks & Rigging

Controller Technical Data

Functions =	Forward, Soft Start, BEC, Cut,
Nominal Voltage =	6 to 10.5 V. (15 V. absolute maximum)
Voltage Drop =	<17 mV / 1 A
Current =	7 Amps Continuous 9 Amps Maximum
Clock frequency =	4 kHz
BEC =	3 V at 0.8 A
Motor rpm reduction =	Voltage < 3 V.
Size =	16mm x 6mm x 4mm
Mass (without wires) =	0.9 g
Mass (with wires and connectors) =	1.8 g

Operation

The controller does not switch off power, but reduces power to 1/4 throttle. This permits slow flyers to land safely. The integrated Auto-Programming module will adjust the controller to your R/C equipment automatically.

SCSH-7A-3: $49.00 each Canadian

Top of Page
Return to Catalogue Index
To Process Your order (Checkout)

SCSH-7A-V Variable Cut Off ESC by SKY HOOKS & RIGGING

for NiCd as well as 2, 3 and 4 Cell LiPo Packs or No Cut Off

2.0 g. by Sky Hooks & Rigging

Controller Technical Data

Functions =	Forward, Soft Start, BEC, Cut,
Nominal Voltage =	6 to 10.5 V (15 V. absolute maximum)
Voltage Drop =	<17 mV / 1 A
Current =	7 Amps Continuous 9 Amps Maximum
Clock frequency =	4 kHz
BEC =	5 V at 0.8 A
Size =	5 x 10 x 23 mm
Motor rpm reduction =	Voltage < 7.2 V.
Size =	16mm x 6mm x 4mm
Mass (without wires) =	1.0 g
Mass (with wires and connectors) =	2.0 g

Operation

Programable for throttle cut down points at 5.1 V., 6 V., 9 V., and 12 V.

#SCSH-7A-V: $69.00 each Canadian

Top of Page
Return to Catalogue Index
To Process Your order (Checkout)

SCWES-6A

1.8 g. 6 Amps
from H. Jung

Controller Technical Data

Functions =	Forward, Soft Start, BEC, Cut,
Nominal Voltage =	6 to 10 V
Voltage Drop =	150 mV / 3 A
Current =	6 Amps Continuous
Clock frequency =	2.5 kHz
BEC =	5 V at 0.7 A
Size =	5 x 16 x 20 mm
Mass (without wires) =	0.9 g
Mass (with wires and connectors) =	1.8 g

Operation

The controller does not switch off power, but reduces power slowly, so that there is still enough voltage available for correct receiver functions. The integrated Auto-Programming module will adjust the controller to you R/C equipment automatically.

#SCWES-6A: $82.00 each Canadian

Top of Page
Return to Catalogue Index
To Process Your order (Checkout)

SCWES-2A

1.2 grams Type 5, 2 Amp Cont. 3 Amp Max. from JMP-France

Controller Technical Data

Functions =
controller, soft start, BEC

Technology =
RISC Microprocessor

Nominal voltage =
6 to 10.8 V (15V max)

Current =
2Amp. continuous 3Amp. max

BEC =
5.0 V, max. 0.7A

Clock frequency =
4.1 kHz

Voltage drop =
17mV / 1A

Size =
4 x 8 x 9 mm

Soft start =
0.75 start to full power

Motor rpm reduction =
Voltage < 5.2V

Mass (without wires) =
0.5 g

Mass (w/ wires &connector) =
1.2 g

Operation

The controller switches off motor rpm at low voltage, so that there is still enough voltage available for correct receiver and servo function. The controllers are delivered with 8cm micro wires and micro plug for battery connection.

#SCWES-2A: $82.00 each Canadian

Top of Page
Return to Catalogue Index
To Process Your order (Checkout)

SCWES-8Bi

4.3 gram 8 Amps Cont. 10 Amp Max. from H. Jung

Controller Technical Data

Functions =
Low voltage detection, BEC

Technology =
RISC Microprocessor

Nominal voltage =
6 to 10.8 V (15V max)

Current =
8 Amp. continuous 10 Amp. max

BEC =
5.0 V, max. 0.8A

Clock frequency =
3.0 kHz

Voltage drop =
<17mV / 1A

Size =
5mm x 16mm x 17mm

Motor rpm reduction =
Voltage < 5.2V

Mass (without wires) =
1.2 g

Mass (w/ wires & connectors) =
4.3 g

Operation

This Bi-directional controller has been developed for models that must have a reversing capability, such as cars, blimps and boats.

It will support 6 to 8 cells with BEC up to 2 servos. Without BEC, it will use up to 10 cells.

#SCWES-8Bi: $96.00 each Canadian


Top of Page
Return to Catalogue Index
To Process Your order (Checkout)

SCWES-HF100

0.9 grams 1.5 Amps High Frequency Controller by JMP of France

Controller Technical Data

Functions =
controller, soft start, BEC

Technology =
RISC Microprocessor

Nominal voltage =
4.2 to 12 V

Current =
1.5 Amp. continuous

BEC =
5.0 V, max. 1 A

Clock frequency =
100 kHz

Voltage drop =
<17mV / 1A

Size =
17mm x 9 mm x 7 mm

Soft start =
0.75 start to full power

Motor rpm reduction =
Voltage < 5.1V

Mass (without wires) =
0.9 g

Mass (with wires) =
2.2 g

Throttle resolution
256 steps

Operation

This controller can improve the efficiency of your coreless propulsion system by up to 15%. The innovative design effectively eliminates the current peaks that tend to destroy the motor brushes, thereby increasing the life of the comutator and brushes of your coreless motors.

#SCWES-HF100: $94.00 each Canadian

Top of Page
Return to Catalogue Index
To Process Your order (Checkout)

GWS-Mini-5A

7.3 g. 5 Amp ICS-100 from GWS

Controller Technical Data

Functions =
Forward, BEC, Cut

Technology =
RISC Microprocessor

Nominal voltage =
5 to 8 Cells NiCad

Current =

5 Amps Continuous
8 Amps Max.

BEC =
5.0 V, max. 1 A

Clock frequency =
3.0 kHz

Voltage drop =
<17mV / 1A

Size =
21.5mm x 10.5mm x 5.5mm

Mass (with wires) =
< 7.3 g

Mass (without wires) =
< 2.0 g

Operation

Featuring high frequency operation, this microprocessor controlled ESC will provide smooth throttle response at a continuous current draw of up to 5 Amps. The BEC circuit cuts the need for a separate battery to power on board R/C equipment.

#GWS-MINI-5A: $30.00 each Canadian

Top of Page
Return to Catalogue Index
To Process Your order

GWS-MINI-15A

17.3 g. 15 Amp
ICS-400 from GWS

Controller Technical Data

Functions =
Forward, BEC, Cut

Technology =
RISC Microprocessor

Nominal voltage =
6 to 10 cells

Current =

15 Amp. continuous
25 Amp. max

BEC =
5.0 V, max. 1 A

Clock frequency =
3.0 kHz

Voltage drop =
<17mV / 1A

Size =
27.5mm x 19.5mm x 6mm

Mass (with wires) =
17.3 g

Mass (without wires) =
4.0 g

Operation

Featuring high frequency operation, this microprocessor controlled ESC will provide smooth throttle response at a continuous current draw of up to 15 Amps. The BEC circuit cuts the need for a separate battery to power on board R/C equipment.

#GWS-MINI-15A: $40.00 CAD equivalent

Top of Page
Return to Catalogue Index
To Process Your order

Micro 10, 5 Amp ESC by Kontronic

0.9 grams 5 Amps by Kontronic

Controller Technical Data

Functions =
Forward, Soft Start, BEC.No cut off.

Technology =
RISC Microprocessor

Nominal voltage =
5 to 8 cells 3-servos

Current =

7 Amp. continuous
10 Amp, max.

Clock frequency =
2.80 kHz

Size =
19mm x 9.5 x 4mm

Mass (without wires) =
0.9 g

Operation

This microprocessor controlled ESC will provide smooth throttle response at a continuous current draw of up to 7 Amps. The BEC circuit cuts the need for a separate battery to power on board R/C equipment.

#SCKO-MICRO-10: $60.00 CAD equivalent

Top of Page
Return to Catalogue Index
To Process Your order

Micro Demon-52, 14 Amp ESC by Viper Model Products

20 grams 14 Amps by Viper

Controller Technical Data

Functions =
Forward, Soft Start, Brake, BEC, Cut,

Technology =
RISC Microprocessor

Nominal voltage =
6 to 8 cells 3-servos

Current =
14 Amp. continuous

Clock frequency =
3.8 kHz

Size =
30mm x 14mm x 7mm

Mass (with wires) =
20 g

Operation

Comes with entegral switch harness for easy installation.

#SCVIP-52: $51.00 each Canadian

Top of Page
Return to Catalogue Index
To Process Your order

Pixie-7 by Castle Creations

3.7 grams 7 Amps by JMP of France

Controller Technical Data

Functions =
Forward, Soft Start, BEC, Cut,

Technology =
RISC Microprocessor

Nominal voltage =
3 to 6 cells 3-servos

Current =
7 Amp. continuous

Clock frequency =
2.80 kHz

Size =
28mm dia. x 15mm

Mass (with wires) =
3.7 g

Mass (without wires) =
< 1.0 g

Operation

#SCCA-PIXIE-7: $66.00 each Canadian

Top of Page
Return to Catalogue Index
To Process Your order

Jeti JE140 Compact

18.1 grams 15 Amps High Frequency Controller by JMP of France

Controller Technical Data

Functions =
Forward, Soft Start, Brake, BEC, Cut, 3 servos

Technology =
RISC Microprocessor

Nominal voltage =
6 to 8 cells

Current =
14 Amp. continuous

Clock frequency =
1.0 kHz

Size =
28mm dia. x 15mm

Mass (with wires) =
18.1 g

Mass (without wires) =
12 g

Operation

This microprocessor controlled ESC will provide smooth throttle response at a continuous current draw of up to 18 Amps. The BEC circuit cuts the need for a separate battery to power on board R/C equipment. Will operate receiver and up to 3 servos. Has current limiter protection that stops motor if it is blocked.

Designed to fit exactly and bolt to the back of any SPEED 400 motor. Comes complete with integral switch harness.

#JE140: $39.00 each Canadian

Top of Page
Return to Catalogue Index
To Process Your order

SKY HOOKS & RIGGING | TO PROCESS YOUR ORDER

All images are copyright stamped for the protection of the originator

All sales are final unless otherwise stated.

The user must determine the suitability of all items for the intended use and assume all risk and responsibility thereof.

How You Can Reach SKY HOOKS & RIGGING

2206 Towne Blvd., Oakville, ON Canada L6H 5H4

Voice 905-257-2101
Fax 905-257-0168
E-mail info@skyhooks.ca
Web www.skyhooks.ca