Micro R/C Indoor Radio Systems from Sky Hooks & Rigging

Welcome to 900Mhz Radio Control! You get a Tx, Rx, Charger, 2 Cells, and Flight Sim cable Plus you also get 2 miniActs, 6mm gearbox, and 100X80 matching propeller. Save money when you buy the Deluxe Set!

Description: The Worlds lightest (production )indoor R/C receiver with 90mAh Lithium cell and the matching HFX900 900Mhz R/C transmitter (full proportional transmitter, with built in Lithium Polymer Charger), also includes flight sim interface cable and a free copy (no charge) of the freeware FMS R/C flight simulator! You may fly with your friends even if they also have the HFX900 System.

Includes: HFX900 Air Model 2 Transmitter, Micro9 0.9g Receiver, Two 90mAh lithium Bahoma Cells and an Flight Sim FMS cable, 6mm gearbox, prop, and 2 magnetic actuators!

Requires: 4 AA cells

$199.99 each Canadian

This set has smaller actuators and Direct Drive motor! You get a Tx, Rx, Charger, 2 Cells, and Flight Sim cable Plus you also get 2 MicroAct Proportional actuators, 7mm Motor, and 2 propeller selections. Save money when you buy the Deluxe Set! You may fly with your friends even if they also have the HFX900 System.

Description: The Worlds lightest (production )indoor R/C receiver with 90mAh Lithium cell and the matching HFX900 900Mhz R/C transmitter (full proportional transmitter, with built in Lithium Polymer Charger), also includes flight sim interface cable and a free copy (no charge) of the freeware FMS R/C flight simulator!

Includes: HFX900 Model 2 Transmitter, Micro9 0.9g Receiver, Two 90mAh lithium Bahoma Cells and an Flight Sim FMS cable, 7mm Motor, 2 different props, and 2 MicroAct Proportional actuators!

Requires: 4 AA cells

$199.99 each Canadian

HFX900 Air Model 2 Transmitter with built In Lithium Charger. Charger is configured for 10mm Bahoma charging a 90mAh cell perfectly. This transmitter is included with our Deluxe Starter Sets.

Description: HFX Air Model 2 Transmitter, built for Plantraco 900Mhz Airplane Receivers. Tx has negative Expo, V-Tail, and Normal mixing modes. Full Proportional 4 Channel Output. 6 user-selectable frequencies. Built-In Precision Lithium Polymer Charger for Bahoma LP90 Cell. FMS flight sim input jack is ready for the FMS flight sim cable available separately. Built-in Buddy Box RJ-12 jack turns your old 72Mhz Hitec or Futaba into 900Mhz , with the addition of the MONOLITH - Bonus Feature!

Includes: Transmitter with built in 10mm Bahoma charger for 90mAh cells

Requires: Plantraco 900Mhz Receiver, such as the Micro9, or other Plantraco 900Mhz receivers and 4 AA batteries.

$74.99 each Canadian

HFX900 Air Model 2 Transmitter with built In Lithium Charger. Charger is configured for 5mm Bahoma for charging 30mAh cell perfectly. This transmitter is what is included with the Butterfly RTF.

Description: HFX Air Model 2 Transmitter, built for Plantraco 900Mhz Airplane Receivers. Tx has negative Expo, V-Tail, and Normal mixing modes. Full Proportional 4 Channel Output. 6 user-selectable frequencies. Built-In Precision Lithium Polymer Charger for Bahoma LP30 Cell. FMS flight sim input jack is ready for the FMS flight sim cable available separately. Built-in Buddy Box RJ-12 jack turns your old 72Mhz Hitec or Futaba into 900Mhz - Bonus Feature!

Includes: Transmitter with built in charger - With non-returning Throttle Stick!

Requires: Plantraco 900Mhz Receiver, such as the Micro9, or other Plantraco 900Mhz receiver products and 4-AA batteries

$74.99 each Canadian

Now you can fly your models with your old HiTec or Futaba transmitter - Compatible with all Plantraco Micro9 Receivers! Good for those flyers who like the feel of the larger sticks on 72Mhz transmitters.

Description: This Monolith will convert your Futaba or Hitec Transmitter with a Din6 Jack into a 900Mhz transmitter compatible with all Plantraco Receivers. Just plug the Din6 plug into the Buddy Box trainer jack. Calibrate once and you are ready to fly!

Includes: The Monolith - Buddy Box Module.

Requires: Futaba or Hitec Transmitter with a Din6 Buddy Box Jack

$49.99 each Canadian

This one has no microconnectors, But it does have our 5mm Bahoma battery terminals. It is suitable ONLY for those who can solder. Works with the HFX900 (USA) and The HFX868 (European Version)

Description: This is presently our lightest receiver, with the added bonus of the Bahoma battery system - weighing in at approx 0.38g. No MicroConnectors, 5mm Bahoma magnets. Output for 1 actuators and 1 motor output. Pure Digital Radio Link, Built-In low voltage protection. Buy the 0.9 gram version unless you really need the lightest receiver and are capable of soldering fine wires to tiny PCB pads. Don't sneeze, it is small!

Includes: One Micro9 Butterfly Receiver, Instruction Manual

Requires: HFX900 Air Model 1 Transmitter, LP30 30mAh Bahoma Cell

$69.99 each Canadian

The Word's Lightest Airplane Receiver! Works with the HFX900 (USA) and The HFX868 (European Version)

Description: It's Super Ultra Pico Nano Micro ----- Do these terms have meaning anymore? This is our most user friendly receiver, weighing in at 0.9g including our Patent pending Bahoma connectors and .05 pin and socket connectors for 2 actuators and 1 motor output. Pure Digital Radio Link, Built-In low voltage protection.

Includes: One Micro9 0.9g Receiver, Instruction Manual

Requires: HFX900 Air Model 1 or 2 Transmitter, Bahoma Battery, 2 MiniAct Actuators.

$69.99 each Canadian

1.2 grams-The Lightest Servo Capable Receiver. That's less than the paper wrapping of your "micro" 72Mhz servo receivers! This one is rock solid pure digital. Smooth action and good range for your Micro R/C models.

Description: Designed for use with WES, Blue Arrow and Falcon servos using “mini-JST” plugs. Built-In 2 Amp motor speed control, Brushless ESC capable. Glitch Free Reliable Micro R/C.

Includes: The receiver, and a Jumper plug for programming, and maybe an instruction manual if you're lucky.

Requires: HFX900 Air Model 1 or 2 Transmitter, Battery with Mini-JST power connector, 1-3 servos.

$56.99 each Canadian

Printed Depron Foam Kits that you can build up in less than 1 hour. They Look Great and They Fly Great! Shoestring Racers have landing gear and are the best taxi-ing plane we have ever flown! The P-51 planes are super flyers and look HOT! Not a toy - these are Full Proportional controlled flying models!

Description: 10-inch Wingspan, Flying Weight of about 12 grams, Flying speed is 2 - 4 m/s approximately. Very stable models that can handle winds outdoors and are fantastic for indoor Micro Pylon Racing. Get One - you'll be addicted like us! You must install the Micro9 3CH receiver, 2 MicroActs, 7mm motor with either the 57x22 prop or the Tri-Turbofan prop, and of course you need HFX900 Tx and LP90 cells.

Includes: Laser Cut Depron Airframe, Control Horns, Z bends and Figure 4's, Carbon Fiber Control Rods, Carbon Fiber FuseStrip, Motor Reinforcments and landing gear.

Requires: YOU NEED the components in the Deluxe Starter Set #2

$18.99 each Canadian

New! 2.5g servos from Blue Arrow. The JST connector pinout is compatible with our 4ch servo receiver.

Description: New! 2.5g servos from Blue Arrow. The JST connector pinout is compatible with our 4ch servo receiver.

Includes: 2.5g servo.

Requires: Plantraco Servo capable receiver

$23.99 each Canadian

1.1 gram bigger actuator - very good for beginnners - plug and play! Does the Job of a servo in your model! FULLY PROPORTIONAL

Description: MiniAct weight is approx 1.1 g and provide ample power for most indoor R/C aircraft. The Nano Connector plugs right into the Micro9 receiver.

Includes: One MiniAct with microconnector installed

Requires: magnet actuator capable receiver from Plantraco!

$18.99 each Canadian

0.41 gram proportional magnet actuator. Low Weight. Does the Job of a servo in your model! FULLY PROPORTIONAL

Description: Plantraco MicroAct magnet actuator weight is approx 0.41 g. 16cm (approx) leads with nano-connector - plugs right into the Micro9 0.9g receiver. This version of the actuator can be used in hinge, and has plastic flanges under the base to fix to rudder or elevator if desired.

Includes: One MIcroAct with 16cm leads

Requires: A magnet actuator capable receiver from Plantraco!

$19.99 each Canadian

HingeAct Actuator - 0.23 grams - Wire leads are about 18 cm length. Self Centering. Torque vs Weight ratio is good! It will kick your plane around all day. 150 Ohm coil, 0.06mm copper magnet wire.

Description: The Lightest commercially available magnetic actuator for Micro R/C Flying. This is the same actuator that is used on our RTF Butterfly Room Flyer. Weight is 0.23 grams, and it can be installed very quickly. Includes solder points on the actuator if you want to run your own wire to the actuator.

Includes: HingeAct Actuator - bare wire leads - requires soldering.

Requires: Micro 9 series receiver and some soldering capabilities on your part to attach to receiver.

$21.99 each Canadian

5.25:1 gear ratio, 0.25 mod gears. 4.5 Ohm motor with 1 mm shaft. Long motor leads, 6 cm, terminated with 0.05 pin connector. Good for props measuring 4 to 6 inches. Draws about 200mAh, depending upon loads. Total weight 2.29 grams.

$16.99 each Canadian

5.85:1 gear ratio, 0.25 mod gears. 4.5 Ohm motor with 1 mm shaft. Long motor leads, 6 cm, terminated with 0.05 pin connector. Good for props measuring 4 to 6 inches. Draws about 200mAh, depending upon loads. Total weight 2.29 grams.

$16.99 each Canadian

This is the gearbox that we use to propel the Butterfly Living Room Flyer. Designed in cooperation with Didel, Switzerland. Unlike regular gearboxes, this one has a stationary axle with 60 tooth spur gear freely spinning on the axle. It works well!

Description: GB05 - 5:1 Gearbox Reduction. 0.2 mod gears. 4mm 13 Ohm motor. Draws about 150mA with the 4027 CF prop attached. Weight with motor is 0.86 grams excluding prop adapter and prop.

Includes: GB05 Gearbox with 4mm motor and Prop Adapter

$19.99 each Canadian

Description: These are great little workhorses, the same motor used in the GB03 and GB04 Gearboxes. These motors have long 60mm leads for easy installation. 1.34g

Includes: 6mm Motor 4.5Ohm for GB03 and GB04

$5.49 each Canadian

This motor is great for a Direct Drive installation on Plantraco's P-51 or Shoestring Racer kits. A Fantastic propulsion unit when combined with the Tri-Turbofan prop or the 57mm X 20mm prop.

Description: These are great little Motors, a direct replacement for the SS Orange (same motor) and has a Micro Connector are pre-installed. These motors have long 60mm leads for easy installation. 1mm Shaft. 2.9g

Includes: One 7mm 3.3Ohm motor and installed Nanoconnector

$5.39 each Canadian

This motor is great for a Direct Drive installation on Plantraco's P-51 or Shoestring Racer kits. A Fantastic propulsion unit when combined with the Tri-Turbofan prop or the 57mm X 20mm prop.

Description: These are great little Motors, a direct replacement for the SS Blue (same motor) and has a Micro Connector are pre-installed. These motors have long 60mm leads for easy installation. 1mm Shaft. 2.9g

Includes: One 7mm 1.7Ohm motor and installed Nanoconnector

$5.39 each Canadian

Capacity 130mAh

Voltage 3.7v Single Cell

Weight 3.7g

Dimensions 25mm x 20mm x 5m

Max Discharge 10C (1300mA)

Connector Type 10mm Bahoma

Replacement 130mAh BAHOMA Cell for the MicroBlimp, or for the HFX900 Micro9-RX-0.9G - 0.9 gram model aircraft receiver. Weight is 3.82grams. Discharge up to 10C (1300mA).

$18.99 each Canadian

Capacity 90mAh

Voltage 3.7v Single C

Weight 2.5g

Dimensions 14.5mm x 23mm x 4.8mm

Max Discharge 15C (1350mA)

Connector Type 10mm Bahoma

Replacement 90mAh BAHOMA Cell for the MicroBlimp, or for the HFX900 Micro9-RX-0.9G - 0.9 gram model aircraft receiver. Weight is 2.5grams. Discharge up to 15C (1350mA). Dimensions are 14.5mm x 23mm x 4.8mm.. Charge with 10 mm Bahoma Transmitter charger combo, or with the BiCha Charger.

$16.49 each Canadian

Capacity 50mAh

Voltage 3.7v Single Cell

Weight 1.8g

Dimensions 13mm x 17mm x 5.7mm

Max Discharge 10C (500mA)

Connector Type 5mm Bahoma

LP50-FR Bahoma Cell - lithium polymer - Replacement cell for the Butterfly Receiver. Weight is 1.8 grams. 50 mAh cell can put out up to 500mA. Should be charged on Plantraco Butterfly transmitter/charger combo - or with the BiCha Charger.

$18.99 each Canadian

Capacity 30mAh

Voltage 3.7v Single Cell

Weight 1.2g

Dimensions 11mm x 17mm x 3.6mm

Max Discharge 10C (300mA)

Connector Type 5mm Bahoma

LP30 Bahoma Cell - lithium polymer - Replacement cell for the Butterfly Receiver. Weight is 1.2 grams. 30 mAh cell can put out up to 600mA. Should be charged on Plantraco Butterfly transmitter/charger combo or BiCha Charger.

$12.99 each Canadian

Capacity 30mAh

Voltage 3.7v Single Cell

Weight 1.2g

Dimensions 11mm x 17mm x 3.6mm

Max Discharge 20C (600mA)

Connector Type 5mm Bahoma

LP30-FR Bahoma Cell - lithium polymer - Replacement cell for the Butterfly Receiver. Weight is 1.16 grams. 30 mAh cell can put out up to 600mA. Should be charged on Plantraco Butterfly transmitter/charger combo or BiCha Charger.

$18.99 each Canadian

Capacity 20mAH

Voltage 3.7v Single Cell

Weight 0.5

Dimensions 11mm x 17mm x 3mm

Max Discharge 20C (400mA)

Connector Type 5mm Bahoma

LP20-FR Bahoma Cell - lithium polymer - Replacement cell for the Butterfly Receiver. Weight is 0.95 grams. 20 mAh cell can put out up to 400mA. Should be charged on Plantraco Butterfly transmitter/charger combo or BiCha Charger.

$18.99 each Canadian

Now you can charge any of your Bahoma cells with this miniature and portable charger. Click on up to 2 Bahoma cells and let them charge - when they are done - the light goes out. Independently charges each cell at rates from 10mA - 150mA, for the smallest lithium cells you have.

Description: BiCHA is a precision portable charger for 1 or 2 Bahoma lithium polymer cells, or bare lithium polymer cells at variable rates of 10 mA to 150 mA. It charges two batteries of different capacities and the charger itself can be powered from from 4 AA batteries, or from an external AC or DC supply.

Includes: Stand-alone BiCha Charger.

Requires: 4 "AA" Batteries or a 6-15v ac/dc Wall Adaptor.

$49.99 each Canadian

Now you can build extensions or whatever you need with these tiny connectors.

Description: These are the smallest, yet still usable connectors we could come up with. The same connector we install on our 6mm gearboxes and MiniAct's. Perfect for updating your actuators to this new, smaller standard. Female Sockets weigh 0.070g Male Pins Weigh 0.048g

Includes: 5 Male and 5 Female Connectors

Requires: Soldering

$18.99 each set Canadian

Description: Great little Propeller, Great for use on our GB03 and GB04 gearboxes. The prop is bored with a 0.98mm shaft hole. The weight is 0.85 Gram

Includes: 100X80 Plastic Prop 1mm bore hub.

$4.89 each Canadian

Description: Great little Propeller, Great for use on our GB03 and GB04 gearboxes. The prop is bored with a 1.5mm shaft hole. The weight is 0.85 Gram

Includes: 100X80 Plastic Prop 1.5mm bore hub.

$4.89 each Canadian

This prop happens to work quite well on our 7mm coreless motor. Experiment.

Description: Replacement Propeller for the Tri-Turbofan Blimp for N20 1mm Hub. Also good for 7mm motor direct drive Micro R/C planes!

Includes: One Tri-Turbofan Blimp Prop 1mm bore hub

$3.99 each Canadian

3.2" x 3.3" prop. Low Weight Carbon Fiber - Beautiful! Good match for GB05 and GB03 Gearboxes

Description: Good match for GB05 and GB03 Gearboxes.

Includes: One 3233 Propeller with prop connector adapter PC0-05

$18.99 each Canadian

3.2" x 2.2" prop. Low Weight Carbon Fiber - Beautiful! Good match for GB05 and GB03 Gearboxes

Description: Good match for GB05 and GB03 Gearboxes.

Includes: One 3222 Propeller with prop connector adapter PC0-05

$18.99 each Canadian

Interface cable for use with HFX900 TRansmitter and your own PC RS-232 Serial Port. Flight Simulator freeware Simulator CDROM is included at no charge. CDROM also includes Plantraco videos and FMS models of plantraco RTF airplanes, and whatever other propoganda we can fit on there for you.

$15.00 each Canadian